# First time Kegging **URL:** \ **Category:** Brewing Processes\ **Created:** [April 30, 2011, 2:09pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127 "2011-04-30T14:09:50Z")\ **Posts on this page:** 15\ **Page:** 1
**Author:** ![tporco](https://avatars.discourse-cdn.com/v4/letter/t/c89c15/32.png) [@tporco](https://forum.homebrewersassociation.org/u/tporco)\ **Post date:** [April 30, 2011, 2:09pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/1 "2011-04-30T14:09:50Z")
Looking for some help/tips on making the jump to kegging from bottling.  Just moved an imperial IPA to secondary so I have a little time but wanted to see if you guys had any tips for a first time kegger.  I purchased a complete setup with regulators and 2 corney kegs so i think i am ok from the equipment side.  Any tips/suggestions on what to watch for? ---
**Author:** ![euge](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/euge/32/5060_2.png) [@euge](https://forum.homebrewersassociation.org/u/euge)\ **Post date:** [April 30, 2011, 2:41pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/2 "2011-04-30T14:41:05Z")
I kept mine simple and just hook up the co2 when needed. Most have a pressure tested system that is “on” all the time. This involves running lines into the fridge somehow, usually by drilling one or more holes in the fridge. If you go the freezer route a “collar” can be added to run all the lines through without drilling into the freezer. Taps can be attached to this collar as well. So you need to decide which route to take. Did you get traditional beer taps or picnic style cobra taps? I’m still using my cobra taps after 4 years. 😉 ---
**Author:** ![wtrice](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/wtrice/32/10658_2.png) [@wtrice](https://forum.homebrewersassociation.org/u/wtrice)\ **Post date:** [May 1, 2011, 12:39am UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/3 "2011-05-01T00:39:53Z")
Keg balancing is what usually trips up new keggers.  The pressure needed to keep your beer carbonated is typically too high for serving if you don’t have significant flow resistance in your beer lines.  As a result you’ll want much longer or much thinner beer lines than you think you need in order to serve a beer that’s not all foam.  As an alternative, you can monkey with the pressure at serving time to reduce the foam, then increase again when the beer will sit a while to keep it from going flat.  Eventually that will become a PITA, but it’ll work until you get everything balanced. ---
**Author:** ![weazletoe](https://avatars.discourse-cdn.com/v4/letter/w/e9bcb4/32.png) [@weazletoe](https://forum.homebrewersassociation.org/u/weazletoe)\ **Post date:** [May 1, 2011, 1:33am UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/4 "2011-05-01T01:33:31Z")
+1 on balancing your system. what seems to work really well for me, I serve at 12psi, with 10’ of 1/4" beer line. Beer stays carbed nicely, and the perfect head every pint. It took me a lot of playing around, and lot of wasted to beer line to figure that out, but once I got, it works like a dream. ---
**Author:** ![liquidbrewing](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/liquidbrewing/32/8224_2.png) [@liquidbrewing](https://forum.homebrewersassociation.org/u/liquidbrewing)\ **Post date:** [May 1, 2011, 1:29pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/5 "2011-05-01T13:29:08Z")
> [@euge](#): > > I’m still using my cobra taps after 4 years. 😉 +1.  I love my Perlicks, but love my cobras too!! Also, I might just give you a little advice about racking.  I noticed you said you had an IIPA that you’re going to be racking soon.  Either give it a long cold crash to get all the hop floaty material out ( I assume you dry hopped) or make sure you siphon from the top of your beer so as to not pick up any hop particulate.  I had a bad experience with this after kegging my first IIPA.  A large piece of a pellet got lodged in the out poppit.  One of the best beers I ever made, but you could only pour about a 1/4 of a glass, as it would foam up like crazy!  Now I use a sanitized paint strainer on the end of my racking tubing to keep all the hop sludge out.  Enjoy kegging, it’s awesome! ---
**Author:** ![oscarvan](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/oscarvan/32/74_2.png) [@oscarvan](https://forum.homebrewersassociation.org/u/oscarvan)\ **Post date:** [May 4, 2011, 6:05pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/6 "2011-05-04T18:05:29Z")
BEFORE you connect the gas hoses to the kegs, put it all together, pressurize it and then close the valve on the bottle. If 24 hours later the pressure hasn’t dropped you’re good to go. If it has, start looking for leaks with Star San or soapy water. (the former is better as you don’t want soap near your beer). Sanitize your keggies. I have a compressor and made a gas and liquid hose with ball connectors on one end and nothing on the other. I clean the kegs, then rinse. Put the air on the gas line and force water out the liquid side. Repeat with sanitizer. Store the keggies with sanitizer in them, pressurized with air. Keeps the seals seated and alerts you if they lose pressure to look for leaks. The most reliable way to carbonate is with the bottle. On service pressure for a week to ten days and you are good to go. If you’re in a hurry you can hook the keg up at 30psi and gently roll it back and forth (end to end). You will hear the CO2 go into solution. 20 minutes or so. Pull the pressure relief vent on the top of the keg to relieve the high pressure and then hook up service pressure. It won’t be perfect but it will be drinkable. Depending on how it is you can also leave it hooked up to high pressure for another day and then drop to service pressure, or just hook it up at service pressure and in a few days it will be just right. Play around with this, you’re get the feel for it. One caution, if you have another keg hooked up, disconnect it when the pressure is cranked up. ---
**Author:** ![tporco](https://avatars.discourse-cdn.com/v4/letter/t/c89c15/32.png) [@tporco](https://forum.homebrewersassociation.org/u/tporco)\ **Post date:** [May 17, 2011, 12:45am UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/7 "2011-05-17T00:45:48Z")
Thanks for the input.  I just replaced all the seals in my keg, cleaned it, filled with sani and pressurized with 30 psi.  if she holds for 24 hours, it sounds like i am good to go.  As liquidbrewing pointed out, there may be a problem with the amount of hops in the 2ndary.  I used a ton of pellet hops in the secondary and i was thining that i would have to strain it somehow to remove all of the hops solids on the way to my keg.  I think i will try to cold crash it for awhile and also strain it thorugh a sterilized hop bag into the keg.  Sound about right? ---
**Author:** ![bluesman](https://avatars.discourse-cdn.com/v4/letter/b/97f17d/32.png) [@bluesman](https://forum.homebrewersassociation.org/u/bluesman)\ **Post date:** [May 17, 2011, 1:24am UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/8 "2011-05-17T01:24:46Z")
Aside from good sanitation practices, I think one of the most important steps in the kegging process is to minimize the amount of oxygen that comes in contact with the beer. One tip is purging the keg with CO2 prior to transfer and then purging the head space after the transfer. Here’s a great kegging manual. [https://files.pbworks.com/download/oxvnokdSFh/draftquality/18182336/DBQM\_Full.pdf](https://files.pbworks.com/download/oxvnokdSFh/draftquality/18182336/DBQM_Full.pdf) ---
**Author:** ![love2brew](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/love2brew/32/13618_2.png) [@love2brew](https://forum.homebrewersassociation.org/u/love2brew)\ **Post date:** [June 3, 2011, 3:20pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/9 "2011-06-03T15:20:55Z")
Some great advice on this thread; here are a ton of links that may help you: Basic overviews: > **[bodensatz.com - This website is for sale! - bodensatz...](http://ww16.bodensatz.com/staticpages/index.php?page=Soda-Kegs&sub1=20240910-0404-51ba-9e20-d346d0d988fd)** > > This website is for sale! bodensatz.com is your first and best source for all of the information you’re looking for. From general topics to more of what you would expect to find here, bodensatz.com has it all. We hope you find what you are searching... [http://brewingtechniques.com/library/backissues/issue5.1/flemingsb1.html](http://brewingtechniques.com/library/backissues/issue5.1/flemingsb1.html) [http://www.ebrew.com/primarynews/intro\_keg\_system.htm](http://www.ebrew.com/primarynews/intro_keg_system.htm) [http://brewingtechniques.com/library/backissues/issue5.1/fleming.html](http://brewingtechniques.com/library/backissues/issue5.1/fleming.html) > **[Kegging-1526397406352-1526857043992.pdf](https://cdn.shopify.com/s/files/1/2785/6868/t/3/assets/Kegging-1526397406352-1526857043992.pdf)** > > 69.05 KB [http://www.reference.com/browse/wiki/Cornelius\_kegs](http://www.reference.com/browse/wiki/Cornelius_kegs) Carbonating/line pressure/line balancing: [http://www.homebrewmart.com/carbona.html](http://www.homebrewmart.com/carbona.html) [http://brewingtechniques.com/library/backissues/issue5.1/flemingsb.html](http://brewingtechniques.com/library/backissues/issue5.1/flemingsb.html) [http://sdcollins.home.mindspring.com/ForceCarbonation.html](http://sdcollins.home.mindspring.com/ForceCarbonation.html) > **[Force Carbonation Chart - Kegerators.com](https://www.kegerators.com/carbonation-table/)** > > A Force Carbonation Chart featuring Pressure vs. Temperature in Degrees Fahrenheit [http://www.ebrew.com/primarynews/ct\_carbonation\_chart.htm#Carbonation\_Chart](http://www.ebrew.com/primarynews/ct_carbonation_chart.htm#Carbonation_Chart) [http://www.kegman.net/equilibrium.html](http://www.kegman.net/equilibrium.html) [http://kegman.net/balance.html](http://kegman.net/balance.html) > **[Crockett Brewing Keg System Balancing](https://www.iancrockett.com/brewing/info/kegbalance.shtml)** > > Balancing your keg system for trouble free pouring Rebuilding: [http://cruisenews.net/brewing/kegging/index.php](http://cruisenews.net/brewing/kegging/index.php) [http://brewery.org/brewery/library/KegCleanDH1095.html](http://brewery.org/brewery/library/KegCleanDH1095.html) > **[bodensatz.com - This website is for sale! - bodensatz...](http://ww16.bodensatz.com/staticpages/index.php?page=Soda-Kegs-Maint&sub1=20240910-0509-0622-9fca-9eacafc768ef)** > > This website is for sale! bodensatz.com is your first and best source for all of the information you’re looking for. From general topics to more of what you would expect to find here, bodensatz.com has it all. We hope you find what you are searching... [http://hbd.org/uchima/kegging/kegadvent.html](http://hbd.org/uchima/kegging/kegadvent.html) O-ring Numbers: [http://www.brewboard.com/index.php?showtopic=34669](http://www.brewboard.com/index.php?showtopic=34669) QD Internal O-Rings: > **[Need source for washer inside ball lock quick disconnect](https://www.homebrewtalk.com/threads/need-source-for-washer-inside-ball-lock-quick-disconnect.73269/)** > > I have a bunch of the beverage-side ball lock quick disconnects, all without the little washer that goes inside of them (spring and pin are OK). For the life of me, I don't know where they went, except probably down the drain. > > Anybody know where I... Replacement Parts: [http://www.simgo.com/replacem.htm](http://www.simgo.com/replacem.htm) > **[Home Brew Kegging Supplies & Equipment](https://www.northernbrewer.com/collections/kegging)** > > Skip the chore of bottling and waiting: with a keg system, you can transfer your beer and be done in minutes, and have force carbonated homebrew in days. [http://kegman.net/soda.htm](http://kegman.net/soda.htm) [http://www.breworganic.com/index.asp?PageAction=VIEWCATS&Category=325](http://www.breworganic.com/index.asp?PageAction=VIEWCATS&Category=325) > **[Undergrounddigital.com may be for sale - PerfectDomain.com](https://perfectdomain.com/domain/undergrounddigital.com)** > > Checkout the full domain details of Undergrounddigital.com. Click Buy Now to instantly start the transaction or Make an offer to the seller! [http://www.thebeeressentials.com/kegging/cornelius-keg-parts.shtml](http://www.thebeeressentials.com/kegging/cornelius-keg-parts.shtml) [http://www.ebrew.com/kegging/cornelius\_parts.htm#top\_of\_page](http://www.ebrew.com/kegging/cornelius_parts.htm#top_of_page) [http://www.williamsbrewing.com/KEG\_PARTS\_C78.cfm](http://www.williamsbrewing.com/KEG_PARTS_C78.cfm) > **[Keg System Hardware](https://www.midwestsupplies.com/collections/kegging-hardware)** > > Quality kegging hardware and equipment to create your own home bar. From gas line assemblies to washer and clamps. [http://morebeer.com/search/102295](http://morebeer.com/search/102295) [http://www.rcbequip.com/productCat15956.ctlg](http://www.rcbequip.com/productCat15956.ctlg) Sanke stuff: [http://sdcollins.home.mindspring.com/ForceCarbonation.html](http://sdcollins.home.mindspring.com/ForceCarbonation.html) Kegging equipment specs and capacities: [http://www.kegman.net/tap\_info.htm#beerline](http://www.kegman.net/tap_info.htm#beerline) Alternative Dispensers: [http://www.angelfire.com/cantina/carbonation/TappingandDispensing.htm](http://www.angelfire.com/cantina/carbonation/TappingandDispensing.htm) Kegerator Tutorials/Blogs/Journals: > **[Kegerator](http://www.thegatesofdawn.ca/wordpress/homebrewing/kegerator/)** > > For the ultimate homebrew experience, the ne plus ultra of beer, you need a draft system. I wanted to build two taps into the bar in my home, but after much head-scratching, I concluded that it couldn’t be done in the space I had to work with. The... [Converting a Sanyo 4912 to be a homebrew kegerator: homebrewing — LiveJournal](http://community.livejournal.com/homebrewing/413981.html) (thanks, Buford!) [http://www.vonnieda.org/blogdetail.jsp?id=805](http://www.vonnieda.org/blogdetail.jsp?id=805) [http://www.chaddickerson.com/gallery/kegerator](http://www.chaddickerson.com/gallery/kegerator) [Brewheads.com - \](http://brewheads.com/kegerator.php) [http://www.kegman.net/rc.html](http://www.kegman.net/rc.html) [http://www.homebrewtalk.com/archive/index.php/t-410.html](http://www.homebrewtalk.com/archive/index.php/t-410.html) [http://www.homebrewblog.com/archives/000012.html](http://www.homebrewblog.com/archives/000012.html) [http://fiberspeed2k.googlepages.com/kegerator](http://fiberspeed2k.googlepages.com/kegerator) [http://www.homebrewtalk.com/f35/sanyo-4912-draft-tower-stabilization-mod-stainless-steel-rail-install-tips-24176/](http://www.homebrewtalk.com/f35/sanyo-4912-draft-tower-stabilization-mod-stainless-steel-rail-install-tips-24176/) [http://forum.northernbrewer.com/viewtopic.php?t=14079&start=0&postdays=0&postorder](http://forum.northernbrewer.com/viewtopic.php?t=14079&start=0&postdays=0&postorder) =asc [https://picasaweb.google.com/KalvinEddie/Sanyo#](https://picasaweb.google.com/KalvinEddie/Sanyo#) [http://forum.northernbrewer.com/viewtopic.php?t=20702&highlight=](http://forum.northernbrewer.com/viewtopic.php?t=20702&highlight=) Tower Assembly: [http://www.homebrewtalk.com/f11/draft-tower-help-24034-post234625/#post234625](http://www.homebrewtalk.com/f11/draft-tower-help-24034-post234625/#post234625) Kegerator Parts Links: Stainless Steel Rails For The Top: > **[Hardware - Lee Valley Tools](https://www.leevalley.com/en-ca/shop/hardware)** > > Shop Hardware Collection on Lee Valley. Browse our extensive selection of functional, decorative fittings to help you find the right finishing touches for any project. Quality Draft Towers: > **[Draft Beer Equipment Manufacturer | ACU Precision Sheet Metal](https://www.acumetalfab.com/index.html)** > > We are a general sheet metal shop with laser cutting services, who have been building Draught (Draft) Beer Equipment since 1959! Shop now for Draft Beer Towers and Draft Beer Drip Trays! If you do not see your beer tower or tray of your dreams, we... Stainless Drip Trays [http://www.barproducts.com/index.php](http://www.barproducts.com/index.php) ‘Bar Supplies’, then ‘Bar Supplies 2’, near end of page-‘Stainless Steel Drip Tray’. Tower Cooling Fans: [http://www.crazypc.com/products/fans/fansmain.htm](http://www.crazypc.com/products/fans/fansmain.htm) [http://www.buyextras.com/fans.html](http://www.buyextras.com/fans.html) [http://www.newegg.com/Store/SubCategory.aspx?SubCategory=573&name=Case-Fans](http://www.newegg.com/Store/SubCategory.aspx?SubCategory=573&name=Case-Fans) [http://www.directron.com/casefans.html](http://www.directron.com/casefans.html) ---
**Author:** ![denny](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/denny/32/13092_2.png) [@denny](https://forum.homebrewersassociation.org/u/denny)\ **Post date:** [June 3, 2011, 3:31pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/10 "2011-06-03T15:31:57Z")
Wow, nice collection of links! ---
**Author:** ![tonyp](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/tonyp/32/12198_2.png) [@tonyp](https://forum.homebrewersassociation.org/u/tonyp)\ **Post date:** [June 3, 2011, 8:15pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/11 "2011-06-03T20:15:56Z")
wow thanks for the links! ---
**Author:** ![tubercle](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/tubercle/32/6256_2.png) [@tubercle](https://forum.homebrewersassociation.org/u/tubercle)\ **Post date:** [June 3, 2011, 10:22pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/12 "2011-06-03T22:22:35Z")
> [@oscarvan](#): > > … If 24 hours later the pressure hasn’t dropped you’re good to go. If it has, start looking for leaks with Star San or soapy water. (the former is better as you don’t want soap near your beer). Question (hand raised): Why not  look for leaks with Star San or soapy water to begin with and save 24 hours of wait time? ---
**Author:** ![maxieboy](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/maxieboy/32/9119_2.png) [@maxieboy](https://forum.homebrewersassociation.org/u/maxieboy)\ **Post date:** [June 3, 2011, 10:48pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/13 "2011-06-03T22:48:10Z")
Mid Michigan first time keggers: don’t take kegging advice from ThingsBeer in Webberville. #Clueless ---
**Author:** ![euge](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/euge/32/5060_2.png) [@euge](https://forum.homebrewersassociation.org/u/euge)\ **Post date:** [June 3, 2011, 11:01pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/14 "2011-06-03T23:01:57Z")
That’s it! I’m buying some taps and retiring my cobras. ---
**Author:** ![maxieboy](https://sea1.discourse-cdn.com/brewersassociation/user_avatar/forum.homebrewersassociation.org/maxieboy/32/9119_2.png) [@maxieboy](https://forum.homebrewersassociation.org/u/maxieboy)\ **Post date:** [June 3, 2011, 11:38pm UTC](https://forum.homebrewersassociation.org/t/first-time-kegging/6127/15 "2011-06-03T23:38:39Z")
> [@tporco](#): > > Looking for some help/tips on making the jump to kegging from bottling.  Just moved an imperial IPA to secondary so I have a little time but wanted to see if you guys had any tips for a first time kegger.  I purchased a complete setup with regulators and 2 corney kegs so i think i am ok from the equipment side.  Any tips/suggestions on what to watch for? A balanced, gas on, leak free system is the only way to fly. Carbonate and serve your beers @ the same temp and pressure. When your beer is kegged, hook it up, 7-10 days later(known as “set it and forget it”), serve. No muss, no fuss. Helpful table: [Force Carbonation Chart - Kegerators.com](http://www.kegerators.com/carbonation-table.php) 10’ of 3/16 ID beer line @ 40\*-45\*(depending on desired volumes of CO2) w/cobra taps or faucets will get you very close. I shoot for a 2 oz/second pour, ideal IMO.